The making of penetrating antenna mast

Hello,

I have been away from my usual radio and electronics activities for a while. Unfortunately i had to venture into the building industry again. Although our new house was finished two years ago, there were two flat roofs that didn’t pass the building inspector watchful eye. One of those was above my office/shack.

After quick quote from few local ‘Mega professional’ roofers it became apparent that i have to do it myself (with the help of the Wifi off course). Simply requirements were too high – installing an access hatch and doing it without scaffold, and most important – penetrating antenna mast. So the incredible price, even before i mentioned my requirements was major put off, and those guys use ancient felt system, where it would seem GRP (fiber glass) was more appropriate for the antenna mast idea.

The actual roof is quite simple – leave the old felt as is too fresh to remove effectively, cover with 80mm insulation, then OSB sheets and lots of 120mm screws to hold all in place, cover all joints with tape to prevent the resin leaking down/covering expansion gaps.

IMG_0635

The biggest complication was the fact that those cemented ridge tiles were below the new flat roof level. It was hard or easy way, we went for the latter – dripping plates above the old ridge, and some glue to hold it all in place. After all this was done – time for the important stuff, hatch access.

IMG_0634

I was lucky in a way, to have the space in the office for small, improvise staircase and clear space on the roof to allow for the hatch.

IMG_0639

The other important design decision was finding correct place for the antenna mast, so it could be attached to the 100x100mm beams that hold my third floor, and be lucky enough that theย  penetrating hole does not interfere with the hatch position and the cemented ridge. Again the antenna God was kind to me and i had the correct spot singled out.

IMG_0642

I know what you think – why didn’t you use proper 110 mm drill extension. Simple reason, the underlying felt made all my drill bits covered in nasty black stuff, didn’t want to spoil brand new looking tool with that !

IMG_0644

Anyway, it was simple job to have nice looking opening for the socket pipe

IMG_0645

At the last minute i have decided to leave the external pipe above the old OSB, for better support and having small hole on the OSB sounded good in case any moisture got through.

IMG_0646

I got perfect fit of the socket pipe and the actual mast.

IMG_0647

And all fits together nicely, next – the actual job of laying the resin.

IMG_0649

We have decided to do this in a two steps (days) operation. First we did all the ridge and dripping plates overlaps, together with the hatch and antenna socket. The second day we covered out the actual flat space.

IMG_0673

Without boring you with any details, here the result. If you are interested how is done, just Google ‘GRP roof’, there are some nice videos on YouTube as well. So after the resin and top coat, i had something like this for my antenna mast socket:

IMG_0678

Don’t mind the temporary 2m vertical, i really don’t have any use for it, but is good for wind testing on the new mast

IMG_0679

Expensive EPDM rubber seal for the joint between the socket and the mast is used. It is very important that provides for waterproofing and mast movement/vibration the same time.

IMG_0680

It is missing a hose clip, just don’t have the right size right now, but yes, there has to be one at the top as well. Here also some details of the mast support inside the house (under the roof).

IMG_0682

After the mast penetrates the lower OSB sheet, it goes via main support truce, in a tight hole.

IMG_0683

Then it lays down on a stud piece that prevents the mast sliding down. There is a variable diameter hole drilled into this piece, so the coax can still be routed out, thus no need to extra waterproofed holes.

IMG_0684

In conclusion – it is not impossible to have penetrating mast on a flat roof. But requires planning, attention to details and probably doing it yourself. It is worth mentioning that i have used quite thin mast, as i don’t require large HF Yagi antennas. I am sure much more rigid construction could be achieved if needed.

Chris

3 thoughts on “The making of penetrating antenna mast

  1. Richard 2E0DVK

    i like it, you could do with a Ex-Military SCAM-12 telescopic mast, hehe tuck it away up the corner of the room, and board round it to hide it and use a compressor on it, 40 foot of goodness, and have a 1.5inch diameter spigott pole in the top of it with your antenna’s on, Then at night time or weekends send her up hehe, would love to do that here, regards Richard 2E0DVK

    Reply
  2. Riyas

    Hi Chris,

    Nice to see the write up on real “home” brewing and the tricks for a leak free mast which wont heavily drain the pockets ๐Ÿ™‚

    73s
    lb7ug

    Reply

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.